IncubationInactivation Water Bath 1013

Microprocessor-controlled temperature regulation.
Excellent temperature constancy: ± 0.1 °C temporal at 50 °C.
Excellent temperature uniformity in the whole bath through built-in circulation system.
Digital temperature readout and setting via LED display, in steps of 0.1 °C.
Soft-touch keys with characteristic symbols.
Electronic monitoring; in case of fault, cause is reported on display.
Two independently working over-temperature protections.
Heating element, bath interior, cover, lid and perforated tray made of stainless steel.
Thermal insulating and double-walled arched lid prevents twisting and dropping back of condensed water into the test tubes.
Lid and perforated tray included as standard scope of supply.
Corrosion proof exterior housing made of electrolytically galvanised sheet steel, powder-coated.
Drain cock at the back of the bath.
The pictured accessories are not included in the unit’s standard scope of supply.

Water Still for single distillation Order No 2004

Water Still for single distillation (fully automatic) with storage tank, suitable for both bench and wall mounting.
Very good distillate quality; conductivity approx. 2.3 µs / cm at 25 °C (see “Technical Details”).
The distillate storage tank accepts twice the hourly capacity of the still.
Electronic level switch switches the still off when the storage tank is full and restarts it automatically when distillate is withdrawn.
Electronic impurity detector switches the unit off in case of high degree impurities of the water in the evaporator, the red pilot lamp “Clean” will glow.
Thermostatic low water cut-off.
Economical energy consumption by distillation of the heated cooling water.
Water saving through automatic water cut-off. Unnecessary water consumption will be avoided.
Evaporator easily accessible for cleaning purposes.
Condenser (cooling coil) inside the storage tank, easily exchangeable.
Distillate withdrawal through drain cock with continuous and touch position.
CO2 degassing through outlet in the condenser.
Heating element, evaporator, storage tank and condenser made of stainless steel.
Double-walled housing. Outer housing made of electrolytically galvanised sheet steel, electrostatically powder-coated with epoxy resin.
Water supply through a built-in solenoid valve with connection for pressure hose 1/2¨ (inner ø approx. 12.7 mm).
Cooling water outlet with hose connection 3/4¨ (ø approx. 19.0 mm).
Hoses for water in- and outlet are available as accessory.

Water Still for single distillation 2008

Power supply through included mains cable (without plug).
Water Still for single distillation (fully automatic) with storage tank, suitable for both bench and wall mounting.
Very good distillate quality; conductivity approx. 2.3 µs / cm at 25 °C (see “Technical Details”).
The distillate storage tank accepts twice the hourly capacity of the still.
Electronic level switch switches the still off when the storage tank is full and restarts it automatically when distillate is withdrawn.
Electronic impurity detector switches the unit off in case of high degree impurities of the water in the evaporator, the red pilot lamp “Clean” will glow.
Thermostatic low water cut-off.
Economical energy consumption by distillation of the heated cooling water.
Water saving through automatic water cut-off. Unnecessary water consumption will be avoided.
Evaporator easily accessible for cleaning purposes.
Condenser (cooling coil) inside the storage tank, easily exchangeable.
Distillate withdrawal through drain cock with continuous and touch position.
CO2 degassing through outlet in the condenser.
Heating element, evaporator, storage tank and condenser made of stainless steel.
Double-walled housing. Outer housing made of electrolytically galvanised sheet steel, electrostatically powder-coated with epoxy resin.
Water supply through a built-in solenoid valve with connection for pressure hose 1/2¨ (inner ø approx. 12.7 mm).
Cooling water outlet with hose connection 3/4¨ (ø approx. 19.0 mm).
Hoses for water in- and outlet are available as accessory.

Water Still for single distillation 2002

Water Still for single distillation (fully automatic) with storage tank, suitable for both bench and wall mounting.
Very good distillate quality; conductivity approx. 2.3 µs / cm at 25 °C (see “Technical Details”).
The distillate storage tank accepts twice the hourly capacity of the still.
Electronic level switch switches the still off when the storage tank is full and restarts it automatically when distillate is withdrawn.
Electronic impurity detector switches the unit off in case of high degree impurities of the water in the evaporator, the red pilot lamp “Clean” will glow.
Thermostatic low water cut-off.
Economical energy consumption by distillation of the heated cooling water.
Water saving through automatic water cut-off. Unnecessary water consumption will be avoided.
Evaporator easily accessible for cleaning purposes.
Condenser (cooling coil) inside the storage tank, easily exchangeable.
Distillate withdrawal through drain cock with continuous and touch position.
CO2 degassing through outlet in the condenser.
Heating element, evaporator, storage tank and condenser made of stainless steel.
Double-walled housing. Outer housing made of electrolytically galvanised sheet steel, electrostatically powder-coated with epoxy resin.
Water supply through a built-in solenoid valve with connection for pressure hose 1/2¨ (inner ø approx. 12.7 mm).
Cooling water outlet with hose connection 3/4¨ (ø approx. 19.0 mm).
Hoses for water in- and outlet are available as accessory.

Water Still for single distillation 20012-2

Water Still for single distillation, suitable for bench mounting.
Very good distillate quality; conductivity approx. 2.3 µs / cm at 25 °C (see “Technical Details”).
Thermostatic low water cut-off.
Economical energy consumption by distillation of the heated cooling water.
Evaporator easily accessible for cleaning purposes.
Destillate withdrawal through outlet at the condenser.
CO2 degassing through outlet in the condenser.
Cooling water temperature indicated through a thermometer.
Heating element, evaporator and condenser made of stainless steel.
Outer housing made of electrolytically galvanised sheet steel, electrostatically powder coated with epoxy resin.
Cooling water in- and outlet 1/2¨ (ø approx. 12.7 mm).
Hoses for water in- and outlet are available as accessory.

Water Bath for fume hoods 1032

Temperature control by tension thermostat.
Protection of the heating element by over-temperature cut-out.
The openings in the lid are covered by heat-resistant plastic 5-part ring sets.
Bath interior, heating element, removable recessed lid and perforated floor cover above the heating element are made of stainless steel.
Four non-slip plastic feet ensure best stability.
Adjustable water level regulator available as a standard scope of supp

Water Bath for fume hoods 1031

Temperature control by tension thermostat.
Protection of the heating element by over-temperature cut-out.
The openings in the lid are covered by heat-resistant plastic 4-part ring sets.
Bath interior, heating element, removable recessed lid and perforated floor cover above the heating element are made of stainless steel.
Four non-slip plastic feet ensure best stability.
Adjustable water level regulator available as a standard scope of supply.

Water Bath for evaporation 1023

Temperature control by tension thermostat.
Protection of the heating element by over-temperature cut-out.
Removable square cover plate (W 265 mm x D 265 mm).
9-part ring set made of heat-resistant plastic. The diametre of the opening can be varied in approx. 20 mm steps.
Heating element, bath interior, frame and perforated floor above the heating element are made of stainless steel.
Corrosion proof exterior housing made of electrolytically galvanised sheet steel, powder-coated.
The adjustable water level regulator 1919 as well as the 9-part ring set are included in the standard scope of supply.

Tissue Float Bath 1052

Very good temperature constancy of ± 0.5 °C.
Exact temperature control guarantees evenly stretched cut tissues which are clearly visible in the bath.
Careful drying of the cut tissues on the warmed rim of the bath.
The low 100 mm height of the bath allows compfortable and safe working.
Bath interior made of aluminium, black anodised.
Housing made of aluminium, powder-coated.
With temperature controller and scale, main switch and two pilot lamps.
Control thermometer fixed to the rim of the bath.

Shaking Water Bath Order No 1083

Microprocessor-controlled temperature regulation.
Excellent temperature constancy: ± 0.1 °C temporal at 50 °C.
Optimum temperature distribution throughout the whole bath interior.
Digital temperature readout and setting via LED display, in steps of 0.1 °C.
Soft-touch keys with characteristic symbols.
Electronic monitoring; in case of fault, cause is reported on display.
Two independently working over-temperature protections.
Maintenance-free and low-wear shaking mechanism, continuously adjustable electronic speed control, gentle start-up.
Constant speed, independent of load.
The shaking device is guided on corrosion-resistant special ball bearings.
Easily removable shaking rack.
Thermal insulating and double-walled arched lid prevents twisting and dropping back of condensed water into the test tubes.
Bath interior and shaking rack made of stainless steel.
Corrosion proof exterior housing made of electrolytically galvanised sheet steel, powder-coated.
Drain cock at the back of the bath.
The pictured accessories are not included in the unit’s standard scope of supply.